Exactly How to Install a Bath Tub
Exactly How to Install a Bath Tub
Blog Article
Nearly everybody will have their personal opinion involving How to Install a Bathtub.
Installing a tub isn't specifically rocket science, however it does call for solid plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old bath tub with a new one is also a reasonably hard project. If the old tub is easily obtainable, the project can move rapidly; if you need to open up a wall to eliminate the old bathtub and also position the new tub, the job is a lot harder. In either instance, the project is within a home handyman's skills, although you will certainly require an assistant to vacate the old tub and set in the brand-new one. Make certain you have actually certified on your own for the job and are comfortable attempting it. Instead of working with a service provider to take over a halfway-completed project, it is much better to think about utilizing one prior to you start. Opportunities are you might require a professional plumber to make tube links.
This short article will certainly assist you set up a brand-new bath tub in your washroom if you have actually currently acquired a brand-new bathtub and also do not require to transform the setup of your previous water pipelines.
Your devices and also product list need to consist of the following:
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you must do is detach the water system. After doing so, switch on the taps to drain any water continuing to be in the system. The procedure of eliminating the existing taps can be fairly troublesome because of the restricted accessibility that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipelines. When the supply pipes have actually been eliminated, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning during this procedure. When the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any old securing compound.
Prior to proceeding to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly need a plastic port to prevent damages to the thread. One end of the port fits on the plastic tail of the tap as well as the other end supplies a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin making certain that the washers remain in area between the faucet and the sink. Protect the faucet in place with the maker provided backnut. When the faucet is securely in position, the supply pipelines can be linked to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal tap adapters. The previous type must be attached to the tap finishes initially, tightening only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bath tub
Using both wood boards under its feet, place the bathtub in the needed placement. The wooden boards are useful in uniformly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four tiny points.
The next objective is to ensure that the tub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the bathtub up until the level reviews level.
To set up faucets, fit all-time low of the furthest versatile faucet adapter to the suitable supply pipe by making a compression sign up with; after that do the same for the other faucet.
Activate the water supply as well as inspect all joints and also brand-new pipework for leaks as well as tighten them if needed. Load the bath tub and likewise inspect the overflow electrical outlet and also the normal outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the supplier's instruction manual. Tiling and sealing around the bathtub must wait up until the tub has actually been utilized a minimum of when as this will settle it into its final position.
Getting ready for the Installation
First of all, the supporting framework provided with the bathroom must be fitted (if called for) according to the supplier's instructions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is essential to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets system to prevent strain on the bath tub.
Fit the adaptable faucet connectors to the bottom of the two faucets making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you make use of every one of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath must now prepare to be suited its final placement.
Tiling Around the Tub
In the area where the bathroom meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can move enough to split a rigid seal, triggering the water to penetrate the wall surface between the bathroom as well as the tiling, bring about issues with dampness as well as possible leakages to the ceiling below.
You can select from a variety of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes as well as cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always fill up the bath tub with water before securing, to allow for the motion experienced when the bathtub is in usage. The sealant can break rather early if you do not take into consideration this movement before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly offered on the marketplace. It is recommended to fit the ceramic tiles making use of water-resistant or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm just very serious about How to Install a Bathtub and I'm hoping you liked the new piece. If you appreciated our article kindly do not forget to pass it around. Thanks for going through it.
Go Deal Now Report this page