Just How To Replace A Bathtub (For Newbies).
Just How To Replace A Bathtub (For Newbies).
Blog Article
Presented here below you can find lots of sound expertise in regards to How to Install a Bathtub.
Setting up a bath tub isn't specifically rocket science, however it does need solid plumbing, carpentry, and also occasionally, tiling skills. Replacing an old bath tub with a brand-new one is also a moderately tough task. If the old tub is easily easily accessible, the job can relocate speedily; if you have to open a wall surface to get rid of the old bathtub and position the new tub, the job is a lot harder. In either case, the project is within a home handyman's skills, although you will certainly require an assistant to vacate the old tub and set in the new one. Make certain you have actually certified on your own for the work and are comfortable attempting it. Instead of employing a specialist to take control of a halfway-completed task, it is far better to take into consideration using one before you begin. Chances are you might require a specialist plumber to make tube links.
This article will help you install a new bathtub in your bathroom if you have actually currently purchased a new tub and also do not require to alter the arrangement of your previous water supply pipelines.
Your devices as well as material checklist need to consist of the following:
Getting ready for the Installation
To start with, the sustaining framework supplied with the bathroom must be fitted (if needed) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is important to see to it that if the tap comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps device to stop pressure on the bathtub.
Fit the adaptable tap adapters to the bottom of both taps using 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its last position.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain any kind of water continuing to be in the system. The process of eliminating the existing taps can be rather bothersome because of the limited access that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the faucets. Have a towel ready for the staying water that will certainly come from the pipes. Once the supply pipes have actually been gotten rid of, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from turning throughout this process. When the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned up of any type of old securing substance.
Before carrying on to fit the new taps, compare the pipe connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Mounting the Tub
Utilizing both wood boards under its feet, place the tub in the called for placement. The wood boards are valuable in uniformly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four tiny points.
The next goal is to make sure that the bath tub is leveled all round. This can be attained by checking the spirit level as well as adjusting the feet on the tub up until the level reviews degree.
To install taps, fit the bottom of the furthest versatile faucet adapter to the ideal supply pipe by making a compression sign up with; after that do the very same for the other tap.
Switch on the water system as well as inspect all joints as well as brand-new pipework for leakages and also tighten them if essential. Load the bath tub as well as additionally examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, fix the bathroom paneling as defined in the supplier's user's manual. Tiling as well as securing around the tub must wait up until the bathtub has been made use of at the very least when as this will settle it right into its last setting.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly require a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the tap and also the various other end provides a link to the current supply pipes.
If you require to fit a monobloc, after that you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin ensuring that the washing machines remain in location between the tap and also the sink. Protect the tap in place with the manufacturer given backnut. Once the faucet is firmly in place, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular tap connectors. The previous kind must be connected to the tap ends first, tightening only by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bath meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to break a stiff seal, triggering the water to pass through the wall surface in between the bath as well as the tiling, causing difficulties with wetness and also feasible leakages to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your components as well as fittings. They are marketed in tubes as well as cartridges, as well as can securing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill up the bathtub with water prior to securing, to permit the activity experienced when the tub remains in use. The sealer can fracture fairly very early if you do not take into consideration this activity before securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise quickly readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water resistant sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a fervent reader on How to Install a Bathtub Yourself, I thought sharing that piece of content was really helpful. Appreciated our content? Please share it. Help someone else find it. Thanks so much for your time spent reading it.
Estimating Report this page